World Card Making Day

World card making day is an awesome celebration.  Getting together with some of your nearest & dearest to craft the day away.  What could be better?  Last weekend I spent the afternoon with 80 crafty ladies making cards, watching demonstrations, checking out samples, and swapping ideas & cards.  I wanted to share my swap card with you.

World Card Making Day
This card is super simple to put together.  I did it in assembly-line fashion since I made 25 of them.  Sit back & enjoy the video, all the supplies and measurements will be listed below.  I use Clear Mount stamps, so you would require blocks if you use them too.

TWW Card base 8 1/2″ x 5 1/2″ scored at 4 1/4″
WW 5 1/4″x 4″   1 1 /2″x 2 1/4″
Garden Green 2″ 2 12″
Basic Black 5″x2″
Copper Foil Sheet scrap
Red Glimmer Paper scrap
Dazzling Diamonds Glimmer paper 4″x 1 3/4″
Post-it notes 3″x3″ for masking
Product List

Season to Sparkle Christmas Card

Season to Sparkle

Merry Music DSP

This card is a mix of two sets and a beautiful Designer Series paper (DSP).  Even though it looks complicated, this is a simple card to make.  BEWARE – your arm will get a work out from cranking the Big Shot to get the tree branches cut!  I was inspired by Sandi MacIver’s tutorial on how to do a bridge card.  Our Chandelier & Christmas Staircase

I was inspired by Sandi MacIver’s tutorial on how to do a bridge card.  Our Chandelier thinlits and Christmas Staircase thinlits spoke to me for this card.   I wanted to show off the pretty silver Christmas tree without blocking it and yet have some sparkly bobbles!  I used window sheet pieces and stamped with Versa Mark some of our heat & stick and dazzling diamonds glitter for the sparkly bobbles from Season to Sparkle stamp set.  One thing I thought of after I completed this card was to find a way to make a color wheel (like we had way back when!)  I will post again when I figure that out.

INSTRUCTIONS & MEASURES:

Thick WW card base 4 ¼”x 8”            scrap Whisper White card stock
Score card base at 1 ¼”, 2 ½”, 5 ½”, 6 ¾”
DSP 4×6 ¾” (make sure your pattern is going in correct direction)
Cut DSP on 6 ¾” side at 1”, 1”, 2 ¾”,1”
4″x6″ Silver foil paper           Embossing Buddy                       Heat Tool
4″x3″ Window sheet              Dazzling Diamonds Glitter         Heat & Stick powder

Adhere DSP to card base from left to right as cut leaving the 2 outside 1”x4 ¼” pieces loose at the top.  Apply a strip of Tear Tape at the top of the 2 outside edges of the card base.   Do not remove the covering on the tear tape, you will be connecting your bridge piece there.

Window sheet – cut ½” strip off.  Rub the embossing buddy over the remaining piece and stamp the swoopy bobbles on the window sheet with Versa Mark ink, quickly cover with Heat & Stick and set with the heat tool.  Quickly dust with  Dazzling Diamonds glitter (shake off excess) and set with heat tool.  Use glue dots to adhere the bobbles in the center of the 1/2″ strip.
On the scrap Whisper White – Stamp your sentiment in Basic Black ink.  Use Layering Oval framelit to cut with Big Shot, and adhere with glue dots to the top of the ½” strip (this will be the bridge).  Set aside.

Run the Christmas Tree & branches through Big Shot on the Silver Foil paper… you will need 7 large branches and multiple small branches.  Adhere the tree to the center back panel with multipurpose glue.  Use multipurpose glue to adhere the large branches first to the solid tree and fill in with the small branches.

Now we fold the card base in mountains & valleys.  Fold in-ward at 2 ½”, then back at 1 ¼” on the left, in-ward at 5 ½”, then back at 6 ¾” on the right.  Burnish the folds carefully, your tree is in the center.

Remove the release paper & line up your bridge piece (below the DSP line) and adhere the left side.  Use another piece of tear tape or snail to adhere the DSP in place.  Fold the left side of your card down with the right side extended.  Remove the release paper & line up your bridge piece (below the DSP line) and adhere the right side.  I used another piece of tear tape or snail to adhere the DSP in place.

Product List